Accessories

With this cable, the control function of the BMS 12/200 charge can be used together with VE.Bus BMS. The BMS 12/200 limit the charging current for the alternator to a safety value, and to terminate the charging process in case of alarm.

Use this cable to connect a Skylla-i to a VE.Bus BMS. The VE.Bus BMS will then disable the Skylla-i charger when the batteries are fully charged.

This cable is intended for on/off control of BlueSolar MPPT solar chargers with a VE.Direct interface.It will switch the product on when the source signal turns high, and switch the product off when thesource signal turns low or becomes free floating.

This interface is used in Hub-1 systems with grid-feedback enabled. It interfaces between the VE.Bus system and one or more MPPT solar chargers with a VE.Can connection: the MPPT 150/70 and/or MPPT 150/85.

The VE.Direct to VE.CAN interface connects products with a VE.Direct connection to products with a VE.Can connection, so the products can communicate with each other.

VE.Direct using Bluetooth Dongle you can view the information of BMV or MPPT monitor on iOS and Android devices, using the VictronConnect application. You can look at the information wirelessly, as the state of the battery, the power of the solar panel, and many other useful data .

This AC current sensor is necessitated for the Hub-4 system, which is the system, which allows to use the Inverter Victron Multiplus Series 3000VA 48V with CEI-021 certified systems of gi & agrave; networked, from the second to fourth energy bill.

MK2-USB interface allows configuration of all devices Victron VE.Bus through the use of a computer.

With the inverting remote on-off cable you can switch the Victron Inverter, that is connected to the MPPT Charge Controller, on/off through the load output of the MPPT Charge Controller.

With the non inverting remote on-off cable you can switch the Victron Inverter, that is connected with the MPPT Charge Controller, on/off through the load output of the MPPT Charge Controller.

These are essential to the proper functioning of the controller Victron Energy BMV series.

These are essential to the proper functioning of the controller Victron Energy only VE.Net Battery Controller series.

These are essential to the proper functioning of the controller Victron Energy

These are essential to the proper functioning of the controller Victron Energy only VE.Net Battery Controller series.

The SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.

The SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.

The SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.

This cable is connected only and exclusively to the Battery Monitor BMV-702, in order to measure the temperature of the batteries and bring them back on the display. It is advisable to install it each time you install a Battery Monitor BMV-702. Note Import:Mounted only on the BMV-702 series, it is not compatible on earlier models.

The VE.Net Tank Monitor allows you to monitor your water, fuel and waste tank tank levels on your VE.Net system. The information is sent over the network to be viewed on a VE.Net Blue Power Panel or VE.Net Panel

MK3-USB interface allows configuration of all devices Victron VE.Bus through the use of a computer. Use the MK3-USB to connect the following products to a computer for configuration: Multi; MultiGrid; MultiPlus; Quattro; Inverter (only models with a VE.Bus communication port); ECOmulti; EasySolar; EasyPlus.

The VE.Can resistive tank sender adapter allows a standard resistive tank level sender to connect to the Color Control GX. It is compatible with both European standard 0-180 Ohm and United States standard 240-30 Ohm tank level senders and is accurate to ±1%. It is easily configurable to resistive senders from fuel, fresh water, waste water, well water,...

Using the VE.Direct to LoRaWAN module you can connect your BMV, MPPT or Phoenix Inverter to the Victron Remote Management portal. View information such as battery status or solar power wherever you are on your desktop or mobile phone.

The VE.Net Tank Monitor allows you to monitor your water, fuel and waste tank tank levels on your VE.Net system. The information is sent over the network to be viewed on a VE.Net Blue Power Panel or VE.Net Panel

The VE.Net Tank Monitor allows you to monitor your water, fuel and waste tank tank levels on your VE.Net system. The information is sent over the network to be viewed on a VE.Net Blue Power Panel or VE.Net Panel